Everything about iphone

How to Unlock the iPhone 3G

2009-01-03T20:30:00.001-05:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=2538

These are instructions on how to software unlock the iPhone 3G for use with any GSM cellphone carrier.

Before you can follow these instructions you must have a jailbroken iPhone and you must be on the 02.28.00 baseband(modem firmware). This means that you must be running the 2.2 firmware. If you used PwnageTool to update to 2.2 from 2.1 you will have to rejailbreak using a QuickPwn jailbreak tutorial for the time being.

To find your firmware and modem firmware(baseband) versions you can follow this tutorial. If you are not on firmware version 2.2 and baseband version 02.28.00 then you need to follow one of these tutorials before unlocking: Mac, Windows

Watch the Video!
For your convenience this tutorial is available in video format also. Click the Watch It button to view the tutorial!

Step One
Press to launch Cydia Installer from your SpringBoard.

Step Two
Press to select the Manage tab at the bottom of the screen.

Step Three
Press to select the large Sources button

Step Four
Press the Edit button at the top right of the screen.

Step Five
Press the Add button at the top left of the screen.

Step Six
Enter http://apt9.yellowsn0w.com/ as the source url and press the Add Source button.

Step Seven
Once the source has been added press the large Return to Cydia button.

Step Eight
Press the Done button at the top right of the screen.

Step Nine
Press to select apt9.yellowsn0w.com from the list of user entered sources.

Step Ten
Press to select yellowsn0w from the list of packages

Step Eleven
Press the Install button at the top right of the screen.

Step Twelve
Press the Confirm button at the top right of the screen.

Step Thirteen
After installation completes successfully press the large Return to Cydia button.

Step Fourteen
Now press the Home button then power off and power on the iPhone. You do this by holding down the power button for 3 seconds then moving the power slider that appears to the right. Press the power button again to turn on the phone.

Step Fifteen
You should now be able to insert the SIM of your choice!

***HINTS: It seems that getting your iPhone to pick up your new carrier can be helped by turning off 3G and perhaps toggling the Airplane Mode switch on and off. If you are still having problems try removing and reinserting the SIM or booting with the new SIM already inside. Finally, you can also try to Reset Network Settings from the Settings:General:Reset Menu.

***IMPORTANT: For those having trouble. The yellowsn0w application can simply be uninstalled. If you have tried all the hints and suggestions and still have problems just use Cydia to remove the package and then reboot. You will then have service with your locked carrier as always.

***THANKS: A big thank you to all the members of the iPhone Dev-Team for all their hard work! It is much appreciated by all.

***UPDATES: The Dev-Team has made the following updates...
1. Soon you’ll see yellowsn0w 0.9.1 in the repos. It uses a much longer delay to let your SIM card initialize. If you have problems with 0.9.0, try this one and wait a full minute after you see homescreen, then reinsert sim card. We need both success and failure reports to tune this across the world, so please be patient (but please also report result!)
2. If you are in the U.S. and are trying this with T-Mobile, you must turn off the 3G switch in Settings. Also if you are good with the command line, you can make it much easier by adding the line -q right after the /usr/bin/yellowsn0w line in /System/Library/LaunchDaemons/org.iphone-dev.yellowsn0w.plist (that’s and advanced tip, hopefully someone will make a boosprefs type of tool for it)
3. No PIN support yet. Remember how we said this was beta? Well we’re still working out the flow for SIMs with PINs enabled. Please disable any PIN you may have on that SIM before trying yellowsn0w, for now..

How to Unlock/Jailbreak Your 2.0 2G iPhone (Windows)

2008-07-24T22:53:00.002-04:00

*Before continuing any further please note a lot of users are having issues with Winpwn. We ourselves had issues creating an ipsw. If you have XP, this tutorial will work flawlessly. However, reports are coming in that it does not work wonders on Vista. Winpwn has been updated to 2.0.0.3, hopefully that should fix a lot of the issues.*

Please keep these notes in mind...

- You MUST do a full uninstall of winpwn before installing the new version
- Make sure you have the latest version of iTunes ( Currently 7.7)
- WinPwn uses 300MB of ram at peak due to the ipsw being extracted in memory
- You must first click browse and load an IPSW to use WinPwn (i thought this was clear)
- For 2.0 only the *5A347_Restore.ipsw files are valid. The 345 image will not work
- If you see Failed to load image catalog/payload catalog, this is fine and won't cause problems
- If you already have service with AT&T do not activate or install Youtube Fix
These are instructions on how to unlock and jailbreak your 2.0, 2G iPhone using Windows and WinPwn.

To follow this tutorial you will need to have iTunes 7.7 installed (make sure to reboot). Also, you may need to download and install .Net Framework if you are on Windows XP.

Step One
Create a folder on your desktop called Pwnage. In it place the following files: Winpwn 2.0.0.3 or Winpwn 2.0.0.3 , 3.9BL , 4.6BL , and the latest 2.0 firmware.

Step Two
Install WinPwn by extracting the downloaded zip from Step One and running the setup executable. Once WinPwn has been installed it will put a shortcut icon on your desktop. Double click to launch the application.

Step Three
Once WinPwn has opened click the Browse .ipsw button.

Step Four
Locate the 2.0 firmware file (iPhone1,1_2.0_5A347_Restore.ipsw) from the Pwnage folder on your desktop and click Open.

Step Five
WinPwn will check the firmware to make sure its valid. Now click the IPSW Builder button.
\

Step Six
The IPSW Builder window will open to the Applications tab. Check to select Cydia and if you are not on AT&T then check to select YouTube Fix.

Step Seven
Click to select the Custom Images tab. From here you can can select
your own boot images.

Step Eight
Click to select the Custom Payload tab. From this tab you can select custom payloads you have created to be automatically installed. We will discuss this in a future tutorial.

Step Nine
Click to select the Advanced tab. Check to select: Activate Phone, Enable Baseband update, and Unlock baseband.

We will also need to load the Bootloader files. Click the Bootloader 3.9 button and then select the BL39.bin file in your Pwnage Folder. Then click the Bootloader 4.6 button and select the BL46.bin file in your Pwnage Folder.

Step Ten
Click the Build .ipsw button at the bottom left to build your custom ipsw firmware file. Navigate to your Pwnage folder and click the Save button.

Step Eleven
Once WinPwn has finished creating your custom firmware then click the iPwner button from the main menu.

Step Twelve
Select the custom firmware file we just built from the Pwnage folder on your desktop and click the Open button.

Step Thirteen
You will then be notified that your iTunes has been Pwned!

Step Fourteen
Next we will need to put the iPhone in the DFU mode and restore using iTunes. To put your iPhone into DFU mode please follow these instructions!

Make sure the screen is in black ( No image of the iTunes on screen ) in the DFU mode.

Step Fifteen
iTunes will prompt you that you are in recovery mode.

Hold down Shift and click the Restore button in iTunes.

A popup window will appear asking you to select your firmware. Select the Custom firmware file we saved in the Pwnage folder and then click the Open button.

Once the restore is complete you will have your iPhone unlocked and jailbroken!

How to Track Stocks on the iPhone

2008-04-23T21:31:00.001-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=988

These are instructions on how to setup your iPhone to track your favorite stocks, indices, futures or bonds.

This tutorial is basic in concept; however, there are a few problems you might run into when doing this by yourself. For example if you were trying to setup the S&P 500 you will notice that a search doesn't yield results!

Step One
Press to launch Stocks from your SpringBoard.

Step Two
Notice that Apple has preset some common symbols for you: Dow Jones Industrial, Apple, Google and Yahoo.

Step Three
To add a stock press the i in the bottom right hand corner of the window.

Step Four
In this screen you will have the ability to add and delete stocks. To delete a stock simply press the "No Entry" icon to the left of the stock symbol. Lets add a symbol by pressing the + button at the top left of the screen.

Step Five
Here is where you can enter a symbol to search for. You will notice that some indices and futures will not be found under a basic search. The iPhone uses Yahoo as its quotes server. So we need to find out the symbol Yahoo uses.

Open http://finance.yahoo.com and locate the index, future, bond etc you would like to track. Notice that beside the name Yahoo puts its symbol in brackets. For example the S&P 500 has the following symbol id: ^GSPC

Take this symbol id and enter it into your iPhone. Its name will appear in the list below. Press to select it.

Step Six
You will not notice the symbol added to your list of Stocks. If you would like your symbols tracked by % change then press the % button at the bottom of the screen. Otherwise press the Numbers button and then press the Done button at the top right of the screen.

Step Seven
Your newly added symbol will not be included in the stock list that your iPhone tracks!

How to Setup an Email Account on your iPhone

2008-04-23T18:44:00.001-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=985

These are instructions on how to setup your POP3 or IMAP email account on the iPhone. This is a relatively simple tutorial but I have received a lot of requests for it.

To perform this tutorial you must have your Email settings. You can obtain these from your Internet Service Provider. You will need to have your username and password as well as incoming and outgoing mailserver addresses.

Step One
Press to select Settings from your SpringBoard.

Step Two
Press to select Mail from the Settings Menu.

Step Three
Press to select Add Account from the Mail Menu.

Step Two
Press to select Other when you are presented with a Welcome to Mail screen.

Step Three
Press to select the type of email account you are trying to setup from the tabs at the top of the screen. In this example I will setup a POP3 email account.

Step Four
You will be asked to enter the information for this email account. Enter your Name, Email Address, and a Description for the account.

Step Five
Scroll down and input the settings for your Incoming Mail Server. Enter your Host Name, User Name and Password.

Step Six
Scroll down to the bottom and input the settings for your Outgoing Mail Server (SMTP). Enter your Host Name, User Name, and Password. Then press the Save button at the top right of the screen.

Step Seven
Mail will then check your mail settings. If it is able to verify the settings you inputed it will add the email account. Now when you press Mail it will take you to your mail account!

Step Eight
To confirm the Advanced settings for your Email you can select Settings from the SpringBoard.

Step Nine
Then select Mail from the Settings Menu.

Step Ten
From the Mail Menu you can set Auto-Check, Shown Messages, Preview length, Font Size, To/CC label, Delete Confirmation, BCC, Signature and Default Account.

Step Eleven
You can also set advanced options for the specific account you just added. It is here that you can turn an email account ON or OFF. From the Mail Menu select the email account you just added

Step Twelve
You can use the Account switch to turn on and off the Email account.

Step Thirteen
Scroll down and press the Advanced button.

Step Fourteen
It is here that you can manage your settings for Deleted Messages, SSL, Authentications, Delete from server and Server Port.

How to Filter iPhone Calls and SMS Using iBlackList

2008-04-16T23:09:00.000-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=953

These are instructions on how to filter your incoming calls and SMS messages using iBlackList for iPhone.

iBlackList allows your to create a blacklist or whitelist for filtering purposes. iBlacklist also features a scheduler which allows you to set the time of day iBlackList is active. The unregistered version of iBlackList allows you to filter 2 numbers. For unlimited numbers your must register. Please see the link at the end of this tutorial.

Step One
Please make sure you have iClarified added to your list of installer sources. To do this click here.

Step Two
Press to launch Installer from your SpringBoard.

Step Three
Press to select the Install tab at the bottom of the screen.

Step Four
Press to select iClarified from the list of Categories

Step Five
Press to select iBlackList from the list of Packages

Step Six
Press the Install button at the top right of the screen.

Step Seven
Press the large red Install button that appears.

Step Eight
You will be notified that you must restart iBlackList once install has been completed. Press the large OK button.

Step Nine
You will be returned to the Categories menu when installation is complete. Press and hold the Sleep/Wake button for 3 seconds until the Power slider appears. Move the slider to the right to power off your iPhone. Then press the Sleep/Wake button again to turn your iPhone back on.

Step Ten
From the SpringBoard press to launch your new iBlackList icon.

Step Eleven
You will be asked to enter a password. Input the number 1 and press the Confirm Access button.

Step Twelve
You will now be taken to the iBlackList home screen. Lets first move the Enabled switch to ON to enable iBlackList.

Step Thirteen
Now to add a number to our BlackList press the BlackList button.

Step Fourteen
Press the Add button at the top right to Add a number.

Step Fifteen
Here we can enter a contacts information in manually or press the Contacts button at the top right to input information from your phonebook.

Step Sixteen
Select a contact from your phone book and then select the phone number you would like to blacklist.

The Display and Phone number fields will then be populated automatically. Press the Add to list button.

Step Seventeen
Notice the number is now added to your BlackList. Press the Back button at the top left to return to the iBlackList menu.

Step Eighteen
Scroll down and ensure Active Mode is set to BlackList. Note: if you want to setup a whitelist of course you would set active mode to WhiteList.

Step Nineteen
Press Settings Calls to modify the settings for call filtering. Here you can set the action to take when a filter call comes in. You can also enable or disable the call filter and set the preferences to save history, delete recent calls, filter restrict number, filter unknown number, show a status bar icon, and vibrate. Press the Save button at the top left hand corner when finished modifying the settings.

Step Twenty
We can also press Settings SMS to modify the filter options for SMS messages. Here you can enable or disable SMS filtering and set the preferences to save history, delete SMS upon receipt, filter unknown number, show a status bar icon, and vibrate. Press the Save button at the top left hand corner when finished modifying the settings.

Step Twenty One
You can press Scheduler from the main menu to set the iBlackList's operation schedule.

Press to select a day of the week and you can modify the hours iBlackList is enabled for that day.

Press the Save button at the top left to return to back to the iBlackList menu.

Step Twenty Two
Finally you can also change your password by pressing the Password button on the main menu. Enter a new password and then press the large red Save password button.

Step Twenty Three
You can now press the Home button to exit iBlackList. When ever you receive a filtered text or call you will notice an icon in your Status bar. Press to launch iBlackList from the SpringBoard.

Step Twenty Four
Press View History from the iBlackList menu.

Step Twenty Five
You will now be able to view your filtered call or message and respond accordingly!

THANKS***:
Thanks goes to the iDevBrTeam (Daniel Antonio, Alexandre Kremer). You can visit their site to register iBlackList for a small fee. http://www.iBlackList.com.br

How to Download Files Using Your iPhone

2008-03-29T23:16:00.001-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=867

These are instructions on how to download files using the Safari browser on your iPhone. It installs the Safari Download Plugin written by hachu and extends it to include more file extensions thanks to spyboy.

File formats supported:
zip, rar, gz, lzh, hqx, dmg, dat, exe, tar, torrent, pdf,
wma, wmv, avi, dll, db, flv, swf (code is there , but i disabled it)
sqlitedb, doc (code there, but aint workin), plist (code there, but dont work)
xls (not workin but code there), ppt, pps, msi, asf, iso, img, bin, rtf, 3gp, ipsw, mp3, mp4, mpeg, mpg, swa.

Step One
Make sure you have added iClarified to your list of installer sources. You can do this by follow the tutorial here

Step Two
Press to launch Installer from your SpringBoard.

Step Three
Press the Install tab at the bottom of the screen.

Step Four
Press to select iClarified from the list of Categories.

Step Five
Press to select Safari Download Plugin (1.1.4) from the list of Packages.

Step Six
Press the Install button at the top right hand corner of the screen.

Step Seven
A confirmation window will appear. Make sure you are on 1.1.4 and press the large OK button.

Step Eight
Once installation is completed you will receive a Notice asking you to reboot your iPhone. Press the large OK button.

Step Nine
You will be returned to the categories list. Press the Home button to return to your SpringBoard. Then press and hold the Sleep/Wake button for 3 seconds. A power slider will appear. Slide this to the right to power off your iPhone. Then press the Sleep/Wake button again to power it back on.

Step Ten
Press to launch Safari from your SpringBoard.

Step Eleven
Navigate to a page that contains a link to a file you would like to download. Press to click the link. A window will appear with a Download and Change Filename button. Press Download to download your file!

NOTE***: The download will go to the /var/root/Downloads folder. I will make a tutorial soon on how to view these files best.

THANKS***: Thanks to hachu and spyboy and everyone else that contributed to the creation of this plugin and its capabilities!

How to Convert Video to iPhone Format Using Kvip (Windows)

2008-03-26T22:34:00.001-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=840

These are instructions on how to convert video to iPhone Format using Kvip and Windows.

Kvip is a utility that converts video files from various formats to a video file that is playable on the iPhone and iPod video (5G/5.5G/6G).

Step One
Download Kvip from here. Save the file to your desktop.

Step Two
Double click the downloaded zip file (release016.zip) on your desktop to open it in Winrar or similar.

Step Three
Extract the contents of the file to a location of your choice. In this example I am extracting the files to a folder called kvip on the Desktop.

Step Four
Open the kvip folder you extracted and double click kvip.exe.

Step Five
A windows will open asking you to select the file you would like to convert. Do this then click the Open button.

Step Six
Kvip will then begin to convert your selected video file.

Once finished a dialog will appear and let you know the name and location of your newly converted video file.

Step Seven
Launch iTunes.

Step Eight
Drag the newly created video file into the iTunes window.

Step Nine
Your video file will then be added to the iTunes library.

Step Ten
Connect your iPhone to the computer. iTunes will automatically detect it. Make sure you select the iPhone from the list on the left.

Step Eleven
Click to select the Video tab.

Step Twelve
Check the Sync Movies checkbox, then check the box next to the movie you just imported into iTunes. Now click the Apply button at the bottom right hand corner to sync your video to the iPhone!

How to Create Ringtones Directly on your iPhone !

2008-03-26T22:32:00.001-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=839

Theses are instructions on how to create a ringtone directly on your iPhone using a song from your iPhone's Music Library.

Step One
Press to launch Installer from your SpringBoard.

Step Two
Press to select the Sources tab at the bottom of the screen.

Step Three
Press the Edit button at the top right.

Step Four
Press the Add button at the top left.

Step Five
Input http://i.danstaface.net into the entryfield and press the large OK button.

Step Six
Press the Done button at the top right.

Step Seven
Press to select the Install tab at the bottom of the screen.

Step Eight
Press to select Multimedia from the list of Categories.

Step Nine
Press to select Ringtones from the list of Packages.

Step Ten
Press the Install button at the top right of the screen.

Step Eleven
Press the large red Install button that appears.

Step Twelve
Once installation finishes you will be taken to the Categories list. Press the Home button. Notice the new Ringtones icon on your SpringBoard. Press it to the launch the application.

Step Thirteen
Press to the image to continue into the program.

Step Fourteen
Press the Start converting button to begin using the application.

Step Fifteen
The program will then do some self checks and search through your Music Library. This make take some time!

Step Sixteen
Eventually you will be displayed your Music Library. Select an Artist that you would like to create a ringtone from.

Step Seventeen
Select the song you would like to use as your ringtone.

Step Eighteen
You will be given the option for Quick Conversion or Advanced Conversion. I would suggest using Advanced Conversion.

Step Nineteen
Use the start and length sliders to adjust the start position and length of your Ringtone. Once satisfied press the Convert Now button.

Step Twenty
The application will then convert your song into a ringtone.

Step Twenty One
You will then be returned to your Music Library. Press the Ringtones button at the top left.

Step Twenty Two
You can now see and delete the ringtones you have created thus far.

Step Twenty Three
To set a ringtone please press the Home button to return to your SpringBoard then press Settings.

Step Twenty Three
Press to select Sounds from the Settings Menu.

Step Twenty Four
Press to select Ringtone from the Sounds Menu.

Step Twenty Five
You will then find your newly created Ringtone in the Standard List.

THANKS***: Thanks to skrew for creating this wonder little app. You get more information and donate here.

How to Keep iPhone SMS Converstions Secret

2008-03-23T17:41:00.001-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=832

These are instructions on how to hide and filter SMS conversations using Pysl. This application was created by Rikk so iPhone users could Protect Your Secret Life. It allows you to setup blacklist and whitelists for SMS conversation filtering. You can then view the filtered messages in an area which is password protected.

Step One
Make sure you have added iClarified as an installer source. You can find instructions on how to do this here.

Step Two
Press to launch Installer from your SpringBoard.

Step Three
Press to select the Install tab at the bottom of the screen.

Step Four
Press to select iClarified from the list of Categories.

Step Five
Press to select Pysl from the list of Packages.

Step Six
Press the Install button at the top right hand corner.

Step Seven
Press the large red Install button that appears.

Step Eight
A notice will appear asking you to Confirm installation. Press the large OK button.

Step Nine
Another notice will appear asking you to reboot your iPhone once installation is complete.

Step Ten
Once installation is complete you will be returned to the Categories menu. Press the Home button to return to your SpringBoard. Notice the new Pysl icon.

Step Eleven
Now hold the Sleep/Wake button for three seconds until you see the Power slider. Slide this to right to turn off your iPhone. Then push the Sleep/Wake button again to turn your phone back on.

Step Twelve
Press the Pysl icon to launch the application.

Step Thirteen
Press Settings to open the Settings Menu.

Step Fourteen
Enter a new password to restrict access to this area then press the Save New Password button.

Step Fifteen
Press the Password Changed button that appears.

Step Sixteen
Press the Back button at the top left of the screen.

Step Seventeen
Press Blacklist from the Welcome screen.

Step Eighteen
Press the Add button at the top right hand corner.

Step Nineteen
Press to Add number from contact

Step Twenty
Select an address book entry from your Contact List.

Step Twenty One
Press to select a Contact's Phone Number to use as a filter.

Step Twenty Two
You will be returned to the Add To Black List screen. Here we have the options to enable three switches.

SMS STOP: hide SMS and store in SMS History
SMS DELETE: hide SMS and delete it "on the fly" (without saving in SMS History..no trace)
CALL STOP: hide CALL and register call in CALL History (not available yet)

I have enabled SMS STOP to hide SMS for this person. Then press the Add contact to list.

Step Twenty Three
You will then be returned to the Blacklist. Press the Back button at the top left.

Step Twenty Four
Switch the Pysl Enable to the ON Position.

Step Twenty Five
Now to test Pysl, send an SMS to the person you just added to your Blacklist. Then reopen Pysl. Notice you are asked for your password!

Step Twenty Six
Select SMS History from the Welcome Screen. You will now find that your SMS is displayed here but it is not displayed in the iPhones MobileSMS.app!

How to Manage Your Calls and SMS With iLog

2008-03-21T19:30:00.001-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=825

These are instructions on how to use iLog. iLog is a call and sms history manager for your iPhone.

Step One
Press to launch Installer from your SpringBoard.

Step Two
Press to select the Install tab from the bottom of the screen.

Step Three
Press to select iClarified from the list of Categories.

Step Four
Press to select iLog from the list of Packages.

Step Five
Press the Install button at the top right hand corner of the screen.

Step Six
Press the large red Install button that appears.

Step Seven
A notice will appear asking you to confirm the iLog install. Press the large OK button.

Step Eight
Once install has completed another Notice will appear informing you of a successful installation. Press the OK button.

You will then be returned to the Categories list. Press the Home button to return to your SpringBoard. Notice the new iLog icon. Press the iLog icon to launch the application.

Step Nine
iLog will open up in the Recent tab. This means it is displaying your Call History. At the top there are three tabs, Missed, Received and Dialed. Press any one of these tabs to view your call history for that section.

Step Ten
If you press the blue right arrow next to any of the calls in the Recent Tab you will see the phone number's address book entry with information as to the duration of the call.

Step Eleven
Press the Log tab at the bottom of the screen to view your full history log. This includes calls as well as SMS history.

Step Twelve
If you press the blue right arrow next to an SMS you can view the message as well as remove it from your history.

Step Thirteen
If you press the Filter button at the top of the Log window you can filter which entries are displayed in the Log.

Step Fourteen
Pressing the Edit button will allow you to delete specific entries.

Step Fifteen
Press to select the Duration tab at the bottom of the screen. This will allow you to view the Last, Dialed, Received, and All Durations. You can choose to reset durations if you like.

Step Sixteen
Press to select the Preference tab at the bottom of the screen. From here your have two options, Genera and Data.

From the General option you can set the log to Show Phone Number, Call On Tap, and set the max historical entries.

From the Data option you can Remove All Calls and Remove All SMS.

THANKS***: Big thanks to Alexander Horuzhiy for creating this application. You can get more information from here

How to Switch iPhone NetServices On and Off Easily

2008-03-20T23:56:00.000-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=775

These are instructions on how to install NetServices and use it to easily control your iPhone's network services.

Step One
Launch Installer from the SpringBoard by pressing its icon.

Step Two
Press to select the Sources tab at the bottom right of the screen.

Step Three
Press the Edit button at the top right hand corner of the screen.

Step Four
Press the Add button at the top left hand corner of the screen.

Step Five
Enter http://homepage.mac.com/hartsteins/copycoders/copycoders.xml as the source address and press the OK button.

Step Six
Press the Done button at the top right corner of the screen.

Step Seven
Press to select the Install tab at the bottom of the screen.

Step Eight
Press to select CopyCoders from the list of Categories.

Step Nine
Press to select NetServices from the list of Packages.

Step Ten
Press the Install button at the top right corner of the screen.

Step Eleven
Press the large red Install button that appears.

Step Twelve
Once installation is complete you will be returned to the Categories menu. Press the Home button to return to your SpringBoard. Notice the new NetServices icon! Press to launch NetServices.

Step Thirteen
You will now be brought to a screen of your Built In Network Services. Notice you can turn on and off: EDGE, Bluetooth, WiFi, Airplane Mode, Int'l Roaming, Mail Fetch, and Auto-Lock.

Step Fourteen
Press the Add-Ons tab at the bottom of the screen. Notice you can turn off additional services such as SSH and AFP.

THANKS**: NetServices is based on source code written by Chris Hoffman with additional code by Peter Iannucci. Erica's Utilities coded by Erica Sadun - EricaSadun.com. GUI Interface designed by Drunknbass - monsterandfriends.com

How to Increase Your iPhone Call History

2008-03-20T06:40:00.000-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=817

These are instructions on how to increase the number of entries stored in your iPhone's Call History. This patch will increase the number of entries you can store to 250!

You must have 1.1.3 or higher firmware installed on your iPhone to install this patch.

Step One
Make sure you have added iClarified as an installer source.

Step Two
Press to launch Installer from your SpringBoard.

Step Three
Press to select the Install tab at the bottom of the screen.

Step Four
Press to select iClarified from the list of Categories.

Step Five
Press to select Call History Patch from the list of Packages.

Step Six
Press the Install button at the top right of the screen.

Step Seven
Press the large red Install button that appears.

Step Eight
You will be notified that you must be on the 1.1.3 or newer firmware. Press the large OK button.

Step Nine
A notification will appear telling you to reboot to enable the patch. Press the large OK button.

Step Nine
You will be returned to the Categories menu once installation is complete. Press the Home button to return to your SpringBoard.

Step Ten
Hold down the Sleep/Wake button until the Power slider appears. Move the slider to the right to power off your iPhone. Then press the Sleep/Wake button to turn the iPhone back on. You should now notice an increase in the amount of entries your Call History will hold!

How to Backup Your iPhone With TimeCapsule

2008-03-17T21:30:00.000-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=802

These are instructions on how to install and use TimeCapsule to make backups of your iPhone.

TimeCapsule is a 3rd party application for iPhone and iPod Touch. It can keep multiple states of a particular program by saving its preferences/settings/databases. These states are restorable.

Currently, the TimeCapsule only supports backup/restore of the following apps: AddressBook’s contacts, Call History, Calendar, Installer’s sources (restore may not work due to permission problem in some firmwares, refer to FAQs for solution), Map’s bookmarks & history, Map’s caches, Notes, Safari’s bookmarks & history, SMS, Transit’s Preferences, Stocks, VoiceMail, Weather, and WorldClock

To install TimeCapsule follow these steps:

Step One
Press to launch Installer from your SpringBoard.

Step Two
Press to select the Sources tab at the bottom right of the screen.

Step Three
Press the Edit button at the top right hand corner of the screen.

Step Four
Press the Add button at the top left hand corner of the screen.

Step Five
Enter http://repo.databinge.com as the source address then press the large OK button.

Step Six
Press the Done button at the top right hand corner of the screen.

Step Seven
Press to select the Install tab at the bottom of the screen.

Step Eight
Press to select Utilities from the list of Categories.

Step Nine
Press to select TimeCapsule from the list of Packages.

Step Ten
Press the Install button at the top right hand corner of the screen.

Step Eleven
Press the large red Install button that appears.

Step Twelve
After the installation is complete you will be returned to the Categories Menu. Press the Home button to return to your SpringBoard. You will notice a new TimeCapsule icon on your SpringBoard.

HOW TO USE TIMECAPSULE
Step One
Launch TimeCapsule by pressing its icon on the SpringBoard.

Step Two
When TimeCapsule opens you will be brought to a list of all the different items that TimeCapsule can backup.

Press to select an item you would like to backup. In this example I will choose Calendar.

Step Three
Notice we are now at a blank Calendar list. Press the backup button at the top right hand corner of the screen.

Step Four
A prompt will appear letting you know that unless you donate you can only make one backup. Press the large OK button.

Step Five
Notice now a new restore point will be created. Press this restore point to view the functions associated with it.

Step Six
A popup will appear asking what you would like to do with the restore point. You can Restore, Rename, Delete, or Email the restore point. In this example I will Restore so press the Restore button.

Step Seven
You will be prompted to confirm the Restore. Press the large Ok button.

Step Eight
You Calendar will now be restored. You can then press the Back button at the top left to return to the list of items for backup.

To learn more about TimeCapsule and its functions you can visit the software page here.

How to Install and Use MobileFinder for iPhone

2008-03-09T23:11:00.000-04:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=773

MobileFinder is a filesystem navigator and launcher for use with your iPhone.

You can use MobileFinder to navigate your system files, launch applications, send files by email, synchronize desktop via ssh and rsync, set file permissions, copy/move/delete files, create files and more. You will find it to be very useful. Just like Finder in OS X. It was created by matt.stoker. Make sure to thank him.

This will work on 1.1.3 and higher iPhones. To follow this tutorial make sure you have BSD Subsystem installed and have added the iClarified Source to Installer.

Step One
Press to launch Installer from the SpringBoard.

Step Two
Press to select the Install tab at the bottom of the screen.

Step Three
Press to select iClarified from the list of Categories

Step Four
Press to select MobileFinder from the list of Packages.

Step Five
Press the Install button at the top right of the screen.

Step Six
Press the large red Install button that appears.

Step Seven
You will be asked to confirm the installation of MobileFinder. Press the large OK button.

Step Eight
Once the installation is complete you will receive a Notice indicating the installation was successful. Press the large OK button.

Step Nine
Installer will return you to the Categories menu. Press the Home button to return to your SpringBoard. Notice the new Finder icon. Press this to launch MobileFinder.

Step Ten
Now lets try to email ourselves a photo to see how MobileFinder can work. Press the ~ button at the top right of the screen.

Step Eleven
Double tap the Media folder.

Step Twelve
Double tap the DCIM folder

Step Thirteen
Double tap the 100APPLE folder.

Step Fourteen
You will now see a list of images! Select an email then click the Send button at the bottom of the screen.

Step Fifteen
Notice that an Email button appears at the bottom left of the screen. Press it.

Step Sixteen
You will be brought to a New Message window which already includes your files/image as an attachment.

THANKS**: Of course thanks to matt.stoker and the other project members: kdbdallas and LSwank. You can view the googlecode page: here

How to Switch iPhone NetServices On and Off Easily

2008-03-09T23:03:00.000-04:00

How to Unlock 1.1.2-1.1.4 iPhones with ZiPhone 2.5 GUI (Windows)

2008-02-29T20:36:00.015-05:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=746
and Zibri's Blog @ http://www.ziphone.org/

These are step by step instructions how to jailbreak and unlock almost any iPhone instantly! No downgrading then upgrading! You can do the unlock from 1.1.2, 1.1.3, or 1.1.4. It will also jailbreak and activate as well as install Installer.app for you!

ZiPhone performs all these functions:
- Unlock will work on 4.6 BL or 3.9 BL
- Jailbreak will work on any OS version.
- Activation will work on any OS version, except for youtube on 1.0.X.
- iErase BL 3.9 Baseband

WARNING: THIS TUTORIAL WILL DOWNGRADE YOUR BOOTLOADER TO 3.9!

NOTE*x.1: To avoid unnecessary issues with bugs it is always recommender to

Put the iPhone into recovery mode(check F.A.Q)
Connect to iTunes 7.6.1 and restore it to 1.1.4 (NOT "upgrade" to 1.1.4!!)

before you try the following steps.

Step One
Download ZiPhone from: here
also download Microsoft .NET Framework Version 2.0 from: here

Step Two
Double click ZiPhone.zip on your desktop to extract the folder ZiPhone..

Step Three
From the extracted ZiPhone folder double click ziphoneGUI.exe to launch the application.

Step Four
Make sure you iPhone is connected to the computer and that iTunes has detected it.

Step Five
You can now activate, jailbreak, and unlock,! Just simply click the Do It All! button.

Step Six
The program will now load zibri.dat. Then it will search for the iPhone. Once found it will tell you to wait for approxiametly 4 minutes.

Step Eight
After this time your iPhone will reboot and it will be activated, jailbroken, and unlocked!!!!

NOTE*x.2: In case you think you messed up the steps(white apple logo issue) or locked the phone you need to put the iPhone back in recovery mode, connect to iTunes 7.6.1, restore it to 1.1.4 before you can try beginning from step one again.

NOTE*x.3: "YouTube problem" try to use an active T-mobile simcard not the AT&T simcard that comes with iPhone. Most probably it will fix the problem!

NOTE*x.4: After completion set up the Wi-Fi first and install BSD Subsystem(see below) first then OpenSSH from Installer.app(make sure Community Source is updated to 3.5/ 3.6 or later by refreshing sources). Also go to your iPhones settings, select GENERAL then choose Auto-Lock and make sure the option there is set to NEVER.

NOTE*x.5: For the first time connecting to iTunes after restoring with Ziphone2.5 set the iPhone as a NEW PHONE then go for Sync!!

How to Install BSD Subsystem on Your iPhone

2008-02-26T14:23:00.000-05:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=687

These are step by step instructions on how to install BSD Subsystem on your iPhone. BSD Subsystem is required before installing many other applications and patches and therefore should be the first package you install on your newly jailbroken iPhone.

Step One
Launch Installer by pressings its icon on your SpringBoard.

Step Two
Press to select the Install tab at the bottom of the screen

Step Three
Press to select System from the list of Categories.

Step Four
Press to select the BSD Subsystem package from the list of System packages.

Step Five
Press the Install button at the top right of the screen.

Step Six
Press the large Install button that appears.

Step Seven
A Notice will appear telling you not to use passwd in 1.1.3. Click the large OK button.

Step Eight
Once the installation is complete you will be returned to the Categories List.

After finishing the BSD Subsystem install you will most likely want to install OpenSSH from System category if it hasn't been installed already.

How to Get iPhone Notifications With Taskbar Notifier

2008-02-25T20:48:00.004-05:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=714

These are instructions on how to get notifications on new email, sms or missed calls using Taskbar Notifier. The Taskbar Notifier was created by m.e.slater and whippinpiccadilly. This version will only work for 1.1.2-1.1.4 iPhones!

Step One
Make sure you have BSD Subsystem installed on your iPhone.

Step Two
Press to launch Installer from the SpringBoard.

Step Three
Press to select the Install tab at the bottom of the screen.

Step Four
Press to select Utilities from the list of Categories.

Step Five
Press to select Taskbar Notifier from the list of Packages.

Step Six
Press the Install button at the top right hand corner.

Step Seven
Press the large Install button that appears.

Step Eight
You will be returned to the Categories List. Press the Home button to return to your SpringBoard. Now hold the Sleep/Wake button down for three seconds to bring up the Power slider. Move this slider to the right to power down your iPhone. Then press the Sleep/Wake button again to restart your iPhone...

NOTE**: You may have to reboot your iPhone twice... If it does not work after one reboot try a second reboot.

THANKS***:
You will now notice either a telephone, email or sms in the top right hand corner of your screen if you have missed any one of those items! A big thanks to m.e.slater and whippinpiccadilly for developing this! Check out the google code page here

How to Use Your iPhone as a Touchpad (Windows)

2008-02-24T14:46:00.000-05:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=705

These are instructions on how to access your Computer using your iPhone as a Wireless Remote trackpad.

Step One
Press to select Installer from your Springboard.

Step Two
Press to select the Sources tab at the bottom right of the screen.

Step Three
Press to select the Edit button at the top right of the screen.

Step Four
Press to select the Add button at the top left of the screen.

Step Five
Enter http://cnp.qlnk.net into the entryfield then press the large OK button.

Step Six
Press the Done button at the top right of the screen.

Step Seven
Press the Install tab at the bottom of the screen.

Step Eight
Press to select Utilities from the list of Categories.

Step Nine
Press to select Touchpad from the list of Packages.

Step Ten
Press the Install button at the top right of the screen.

Step Eleven
Press the large Install button that appears.

Step Twelve
When Touchpad is finished installing you will be returned to the Categories list. Press the Home button to return to your Springboard, then press the Touchpad icon to launch the program.

Step Thirteen
Now on your computer download an install TightVNC from here

Step Fourteen
Launch TightVNC Server by selecting it from the Program list.

Step Fifteen
Change the Primary password and View-only password to a password of your choice.

Than click the Apply button.

Step Sixteen
Press the Windows key and R at the same time to bring up the Run window. Enter cmd into the field and click the Ok button.

Step Seventeen
When the command prompt appears, type in ipconfig /all and press the Enter key. Take note of your IP Address... In this case my IP is 192.168.0.199.

Step Eighteen
Back on your iPhone, press to launch Touchpad from the Springboard.

Step Nineteen
Press the + button at the top right of the screen.

Step Twenty
You will now be presented with the Edit Server screen. Enter a name from the computer you are connecting to. Enter an Address for the computer as well. (You can find this address from the screen in Step Seventeen.) Enter the password you set in Step Seventeen. Then, when you have entered all those settings you may press the Save button at the top right.

Step Twenty One
Now that you have configured your server you may press to select it from the list of servers.

Step Twenty Two
Now that you have connected to your computer you can use your iPhone as a Touchpad!!!

Thanks***: Big thanks goes out to Jahanzeb for creating this app!

How to Increase the Volume of Your 1.1.3 iPhone

2008-02-24T14:43:00.000-05:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=712

These are instructions on how to increase the volume on your 1.1.3 iPhone using an Installer source. Remember your iPhone speaker isn't very powerful so it will only be a slight improvement but its better then before :)

Step One
Make sure you have iClarified added as an installer source. You can find directions on how to do that here.

Step Two
Press to launch Installer from your Springboard.

Step Three
Press to select the Install tab at the bottom of the screen.

Step Four
Press to select iClarified from the list of Categories.

Step Five
Press to select Volume Boost (1.1.3) from the list of Packages.

Step Six
Press the Install button at the top right hand corner of the screen.

Step Seven
Press the large red Install button that appears.

Step Eight
You will get a Notice telling you that this process will patch your iPhone to increase its maximum volume! Press the large OK button.

Step Nine
When the installation is done you will get a Notice telling you that your volume has been patched and to restart your iPhone. Press the large OK button.

Step Ten
You will be returned to the Categories list. Hold down the Sleep/Wake button for 3 seconds to bring up the Power slider. Slide it to the right to turn off your iPhone. Then push the Sleep/Wake button again to turn back on the phone!

You will now notice an increase in the volume of your phone :)

How to Free Space on Your iPhone Root File System

2008-02-23T08:56:00.000-05:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=651

These are instructions on how to free up space on your iPhones Root File System.

Step One
Press to launch Installer from your Springboard.

Step Two
Press to select the Install tab at the bottom of the screen.

Step Three
Press to select Utilities from the list of Categories.

Step Four
Press to select Boss Tool from the list of Packages.

Step Five
Press to select the Install button at the top right of the screen.

Step Six
Press to select the large Install button that appears.

Step Seven
When the install completes you will be returned to the Categories Menu. Press the Home button to return to your Springboard. Now press BossTool to launch the application.

Step Eight
Press to select Free Disk Space from the menu.

Step Nine
Press to select Relocate Fonts from the menu. Note we could relocate other stuff but fonts is about 84MB so that is more then enough! Also take notice this screen will display how much free space you currently have available.

Step Ten
Press the large Do It! button to continue.

Step Eleven
After a few minutes you will be returned to the Free Disk Space menu and you will now see 84MB extra space on your root file system!

NOTES***: Big thanks goes out to Big Boss for creating this tool! Much appreciated. If you are considering moving Applications then don't forget to set Auto-Lock to never.

How to Copy Contacts From Your SIM Card to Your iPhone

2008-02-23T08:50:00.000-05:00

All the credits go to iClarified @ http://www.iclarified.com/entry/index.php?enid=698

These are step by step instructions on how to copy contacts from your SIM Card to your iPhone.

Before attempting this tutorial please make sure you have BSD Subsystem installed on your iPhone.

Step One
Make sure you have the iClarified Installer Source added to your Installer App. You can find instructions on how to do that here

Step Two
Press to launch Installer from on your SpringBoard.

Step Three
Press to select the Install tab at the bottom of the screen.

Step Four
Press to select iClarified from the list of Categories.

Step Five
Press to select SIMport from the list of Packages.

Step Six
Press to select the Install button at the top right of the screen.

Step Seven
Press to select the large red Install button that appears.

Step Eight
Once the package has downloaded and finished installing you will be returned to the Categories list. Press the Home button to return to your SpringBoard. From your SpringBoard press to select the new SIMport icon.

Step Nine
You will be displayed a loading screen and then a list of the contacts on your SIM Card will be displayed.

Step Ten
By default all the contacts are selected for import. If you wish to deselect all the contacts the press the Uncheck all button at the top left. If you wish to deselect one contact then press to select the contact and slide the Add to selection switch to OFF. Then press the Back button at the top left to return to the list.

Step Eleven
When done selecting the contacts for import press the Import button at the top right to begin.

Step Twelve
Once the import has completed a notice will appear letting you know how many contacts were successfully imported. Press the large Close button.

You can now check your address book to see the contact you just imported!

THANKS*: This app was developed by alexf from hackint0sh. Big thanks go out to him!

iPhone 1.1.3 Language pack (correction)

2008-02-19T02:59:00.004-05:00

Here is the language interface & keyboard format package for iPhone 1.1.3

Download Pack

The pack contains the following languages:

English
French (Francais)
German (Deutsch)
Japanese ()
Dutch (Nederlands)
Italian (Italiano)
Spanish (Espanol)
Portuguese (Portugal)
Danish (Dansk)
Finnish (Suomi)
Norwegian (Norsk Bokmal)
Swedish (Svenska)
Chinese
China,
Chinese (中文)
Polish (Polski)
Russian (Русский)
Taiwan
Korean

To enable the full language settings, first unzip the downloaded file. You will need to transfer the four unziped folders(Applications,Library,System, and _MACOSX) to root directory of your iPhone. Make sure you overwrite all previous files. It will take about 10~20 minutes through Wifi.

If you need to edit or transfer files on the iPhone and you are using windows, WinSCP is the program you need.

First make sure to install BSD Subsystem first then OpenSSH from Installer.app before you try WinSCP. Next get WinSCP and find your iPhone’s IP by going to (on your iPhone)
settings > Wi-Fi > “Your selected WiFi” > Look under IP Address- Connect to your iPhone using WinSCP (user: root password: alpine) Change File Protocol to SCP

Just press login after your screen on WinSCP.

click on the “..” until you see root, then put four unziped folders (Applications,Library,System, and _MACOSX) inside root directory by dragging and dropping.

Once you have it installed and restart your iPhone you can find the language options in
settings > General > International

Here you also have the Language of the system option, Keyboards option, and the Region Format option.

ENJOY!!

Frequently Asked Questions (F.A.Q)

2008-02-18T09:57:00.005-05:00

What do I do if iTunes stopped recognizing my iPhone?

If iTunes suddenly decides it doesn't like your iPhone, and will not recognize or sync you can remove the Lockdown plist and it will be automatically generated next time you sync the phone.

On a Mac:

1. Close iTunes
2. Open Terminal
3. run rm ~/Library/Lockdown/*.plist
4. Close Terminal
5. Start iTunes
6. Sync your iPhone

On a Windows machine:

1. Close iTunes
2. Open Command prompt
3. run del C:\Documents and Settings\YOUR USERNAME HERE\Application Data\Apple Computer\Lockdown\*.plist
4. Close Command prompt
5. Start iTunes
6. Sync your iPhone

How to Soft Reset (Turn Off) Your iPhone?

To power off your iPhone (Sometimes called a soft reset) follow these instructions:

Step One
Hold down the Sleep/Wake button for 3 seconds.

Step Two
A Power Slider will appear on the screen. Move this slider to the left to power off your iPhone.

Step Three
Press the Sleep/Wake button again to power back on your iPhone.

How to put an iPhone into Recovery mode?

Step One
Open iTunes.

Step Two
Press and hold the down the Sleep/Wake for 3 seconds. A power slider will appear. Slide it to the right to power down the iPhone. Then keeping ONLY the Home button pressed, connect the iPhone to the dock.

Step Three
Keep the home button pressed until you see the iTunes logo and cable on the screen.

Step Four
your iTunes will pops up a message telling you that it has detected an iPhone in recovery
mode.

how to back up iPhone Contacts on a PC?

- Open iTunes on your computer that you sync it to

- Plug in your phone to the computer.

- open "Address book" window's address book program. Its under start->programs->accessories.

- Back to iTunes, click on the phone icon on the left

- Click on the Info, and under "Contacts" (the first one) check "sync contacts from" and then pick "Windows address book" from the drop down menu

- Click all contacts

- Then at the bottom right of iTunes, click "Sync" It will ask you if you want to merge or replace. Make sure you select "MERGE" or it will delete your contacts on the phone.

Thats it, check your Windows Address Book and everything should be there. All the numbers and emails that you have put so much time into adding to your phone. Pretty nice.

So, from now on, if you add contacts to the phone it will back up to the Computer and the Computer's Address book (if changed) adds new contacts.

How to activate T-mobile Edge on your iphone?

make sure you have upgraded to TMobile Total Internet ($19.99)

Turn off the Wi-Fi of your iPhone

After going to Settings>General>Network>EDGE

add the APN name manually to "internet2.voicestream.com"

leave user name and password blank

Will notice the blue "E" letter next to the T-Mobile on the iPhone and

you should be able to surf internet without Wi-FI.

If this doesn't work for you you may be in a GPRS-only zone Or call T mobile customer service.

How to fix Dialer Crashing and Caller ID problems for International iPhone user

2008-02-17T17:09:00.001-05:00

All thanks goes to iClarified @ http://iclarified.com/entries/index.php?caid=2&scid=11

These are instructions on how to patch AppSupport for 1.1.4 iPhones. This fixes Dialer Crashing and Caller ID problems for International iPhone user. If when you try to make a call the keyboard crashes and returns you to the home screen then this is the tutorial you should follow.

This solution was created by timschuerewegen. He deserves all the credit for it!!

Currently this solution has support for the following countries:

Anguilla, Antigua and Barbuda, Argentina, Australia, Austria, Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize, Bermuda, Bosnia and Herzegovina, Brazil, Canada, Cayman Islands, Chile, China, Costa Rica, Croatia, Cyprus, Dominica, Dominican Republic, Falkland Islands (Malvinas), France, French Guiana, French Guiana (workaround for MCC 340 problem), Georgia, Germany, Greece, Grenada, Guadeloupe, Haiti, Honduras, Hong Kong, Iceland, India, Indonesia, Iran, Islamic Republic of, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kuwait, Lebanon, Macedonia, Madagascar, The Former Yugoslav Republic of, Malaysia, Malta, Martinique, Martinique, Mexico, Moldova, Republic of, Montenegro, Montserrat, Morocco, New Zealand, Norway, Panama, Peru, Philippines, Poland, Portugal, Qatar, Romania, Russian Federation, Saint Kitts and Nevis, Saint Lucia, Saint Vincent and The Grenadines, Saudi Arabia, Serbia and Montenegro, Singapore, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Thailand, Trinidad and Tobago, Turkey, Turks and Caicos Islands, Ukraine, United Arab Emirates, United Kingdom, United States, Uruguay, Venezuela, Viet Nam, Virgin Islands, British

Before you start make sure you have BSD Subsystem Installed on your iPhone.

Step One
Launch Installer by pressing its icon on your SpringBoard.

Step Two
Press to select the Install tab at the bottom of the screen.

Step Three
Press to select iClarified from the list of Categories.

Step Four
Press to select AppSupport Patch (1.1.4) from the list of Packages.

Step Five
Press to select the Install button at the top right of the screen.

Step Six
Press the large red Install button to begin the installation.

Step Seven
A Confirm notice will appear telling you that this process will patch AppSupport and to make sure you are on the 1.1.4 firmware. Press the large OK button.

Step Eight
Once the install has completed a Notice will appear telling you that AppSupport is patched. Also you will have to restart your iPhone for the changes to take effect. Click the large OK button.

Step Nine
You will be returned to the Categories menu. Press the Home button to return to your springboard. Now hold down the Sleep/Wake button for 3 seconds to power off your iPhone. Drag the power slider that appears to the right.

After the iPhone turns off you may restart it and finally have use of your phone!

This solution was entirely developed by timschuerewegen. It can be customized to your country if it isn't included already. I will do a tutorial on that later. If you want to donate or to see the latest updates to his patch you can go: here

iPhone | How to Unlock iPhone 1.1.3 with ZiPhone 2.0 GUI (Windows)

2008-02-13T02:45:00.001-05:00

All the credits go to iClarified @ http://iclarified.com/entries/index.php?caid=2&scid=11
and Zibri's Blog @ http://www.ziphone.org/

These are step by step instructions how to jailbreak any iPhone instantly! No downgrading then upgrading! You can do the jailbreak from any firmware. It will also jailbreak and activate as well as install Installer.app for you!

ZiPhone performs all these functions:
- Unlock and will work on 4.6 BL or 3.9 BL.
- Jailbreak will work on any OS version.
- Activation will work on any OS version, except for Youtube on 1.0.X.
- iErase BL 3.9 Baseband

How to determine if your iPhone has the new 4.6 bootloader:

Option one:
If your phone shows this image first time you started it then you have a iPhone with 1.1.2/1.1.3 and bootloader 4.6 . If your phone had a picture of the earth only when you started it first time then most probably you have bootloader 3.9 in your phone.

Option Two:
On the back of the phone (or, if the phone is unopened, on the back of the box), you will see the serial number.
The 4th and 5th digits in the serial number are the week your iPhone was manufactured.

If your iPhone was manufactured in the week 44 or less: Your iPhone has the 3.9 bootloader.

If your iPhone was manufactured in the week 45: There is a slight chance your iPhone may have the 3.9 bootloader, but an even higher chance that your iPhone has the 4.6 bootloader.

If your iPhone was manufactured in the week 46 or over: Your iPhone has the 4.6 bootloader. All European iPhones also come with the 4.6 bootloader.

UPDATE*: It seems that the 2.0 Apple logo problem can be solved by running ZiPhone in verbose mode.

Step One
Download ZiPhone from: here

Step Two
Double click ZiPhone.zip on your desktop to extract the folder ZiPhone..

Step Three
From the extracted ZiPhone folder double click ziphoneGUI.exe to launch the application.

Step Four
You must put your iPhone into recovery mode. To do this please hold down both the Sleep/Wake for 3 seconds. A power slider will appear. Slide it to the right to power down the iPhone. Then keeping ONLY the Home button pressed, connect the iPhone to the dock. Keep the home button pressed until you see the iTunes logo and cable on the screen.

Step Five
If you have a 4.6 BL iPhone you can now activate, jailbreak, unlock, and verbose! Just simply check the Activate, Jailbreak, Unlock, and Verbose checkboxes. Then click the Start button.

Step Six
The program will now load zibri.dat. Then it will search for the iPhone. Now connect the iphone's USB cable to your computer. Once found it will tell you to wait for 2 minutes and 30 seconds.

Step Eight
After this time your iPhone will reboot and it will be activated, jailbroken, and unlocked!!!!

NOTE*x.1: In case you think you messed up the steps(white apple logo issue) or locked the phone you need to put the iPhone back in recovery mode, connect to iTunes 7.6, restore it to 1.1.3 and kill iTuneshelper.exe from Windows task manager (Alt+Ctrl+Delete) before you can try beginning from step one again.

NOTE*x.2: "YouTube problem" try to use an active T-mobile simcard not the AT&T simcard that comes with iPhone. Most probably it will fix the problem! AT&T customers check Andrew's suggestion about this issue @ comment section.

NOTE*x.3: To ONLY jailbreak (because it breaks open the iPhone’s file system so that you can modify the user interface) the iPhone 1.1.3 Firmware for Third Party Application for legitimately activated AT&T iPhone make sure to simply check the Activate, Jailbreak, and Verbose checkboxes at Step Five. Then click the Start button.

Everything else remains the same from the tutorial above. Also make sure to upgrade your iPhone to 1.1.3 via iTunes 7.6 before you even try from step one.

NOTE*x.4: After completion its probably a good idea to install BSD Subsystem first then OpenSSH from Installer.app. Also go to your iPhones settings, select GENERAL then choose Auto-Lock and make sure the option there is set to NEVER!!

NOTE*x.5: If you have a 3.9 bootloader iPhone try iclarified Tutorial How to Unlock Your 1.1.3 3.9 Bootloader iPhone. This will insure all the software function including locate me in Google Maps works great after unlocking your 3.9 Bootloader iPhone with AnySIM 1.3!